Cake Central › Cake Forums › Cake Talk › Cake Decorating › FRUSTRATED with silicone lace molds
New Posts  All Forums:Forum Nav:

FRUSTRATED with silicone lace molds

post #1 of 20
Thread Starter 
I've been doing cakes for several years now, and for some reason haven't had much call for lace. Recently, Decorate the Cake had a Black Friday sale on their lace molds and I bit the bullet and bought 5 of them. I have had minimal success using them. What am I doing wrong? I read somewhere that the fondant is rolled out, pressed into the bottom mold, the top piece is applied and then gently but firmly rolled from the center out. I've gotten sloppy results with all five of the molds. No matter how carefully I press the fondant into the bottom and roll, the molds shift and the impression either ends up with holes, remains too thick or slides and destroys the pattern. Very frustrated and irritated at the cost of these things (even on sale)
HELP! icon_cry.gificon_cry.gificon_cry.gif
post #2 of 20
Are they double sided molds?
Edna
Visit my website.. www.designmeacake.com
http://designmeacakeblog.blogspot.com/
Check my Gumpaste Tutorials in You tube
http://www.youtube.com/user/tonedna1
Check my new Blooms and Vines DVD!



Thanks Edna
Reply
Visit my website.. www.designmeacake.com
http://designmeacakeblog.blogspot.com/
Check my Gumpaste Tutorials in You tube
http://www.youtube.com/user/tonedna1
Check my new Blooms and Vines DVD!



Thanks Edna
Reply
post #3 of 20
Thread Starter 
Hi, Edna! Yes they are.
post #4 of 20
Roll the gumpaste in a flat surface, just like if you where going to do any cutout.
Then place the gumpaste on the mold and press it with your hands. Take the top part
of the lace and place it on to of the gumpaste and use a rolling pin to help you press.
If the gumpaste is good quality it shpuld break pretty easy, so pull the excess pieces of
gumapste with the top part still holding the gumpaste.
The take the top press how and push the excess gumpaste to the inside of the mold to
clean the edges.

Edna icon_smile.gif
Visit my website.. www.designmeacake.com
http://designmeacakeblog.blogspot.com/
Check my Gumpaste Tutorials in You tube
http://www.youtube.com/user/tonedna1
Check my new Blooms and Vines DVD!



Thanks Edna
Reply
Visit my website.. www.designmeacake.com
http://designmeacakeblog.blogspot.com/
Check my Gumpaste Tutorials in You tube
http://www.youtube.com/user/tonedna1
Check my new Blooms and Vines DVD!



Thanks Edna
Reply
post #5 of 20
Thread Starter 
What you have described is what I have done. I'm using Satin Ice. The molds are VERY soft...could that be why this is happening?
post #6 of 20
Try mixing gumpaste or tylose with the Satin Ice, to stiffen it up a little.
post #7 of 20
Thread Starter 
The fondant seems stiff enough...I'm still thinking the silicone is too soft.
post #8 of 20
I havent tried them. I have used the CK ones. I Might have to buy one to see how they are. CK ones are more stiff. But its a matter of figuring them out.
Edna icon_smile.gif
Visit my website.. www.designmeacake.com
http://designmeacakeblog.blogspot.com/
Check my Gumpaste Tutorials in You tube
http://www.youtube.com/user/tonedna1
Check my new Blooms and Vines DVD!



Thanks Edna
Reply
Visit my website.. www.designmeacake.com
http://designmeacakeblog.blogspot.com/
Check my Gumpaste Tutorials in You tube
http://www.youtube.com/user/tonedna1
Check my new Blooms and Vines DVD!



Thanks Edna
Reply
post #9 of 20
I have used their molds. Tylose is a must ,I roll out the fondant/tylose to a little thicker ,place in mold and and place top and press. you might try flipping and press the mold from the top. Have you just tried to use the mold without the top pressed in? And cut away with an exacto knife.
post #10 of 20
I always want to buy lace molds, but I'm afraid of the same thing...not know how to use them!! icon_redface.gif
"Life is short...eat cake!"
Reply
"Life is short...eat cake!"
Reply
post #11 of 20
If you're trying to do this with First Impression molds; I feel your pain.

I've never figured out how to get the excess out!

That's why I own every file known to mankind. Home Depot and Sally's are big friends of mine.
MaryAnn, aka Gomo
Reply
MaryAnn, aka Gomo
Reply
post #12 of 20
Thread Starter 
These are Decorate the Cake molds, MaryAnn. I've not had any trouble with my First Impression molds, though I don't have any lace ones. The edges of all the tops of these two piece molds are so chopped up and gouged that the fondant doesn't pull away evenly on any of them. I've tried adding tylose (which makes the fondant tougher and drier) and am using a quality fondant. The molds themselves are actually so soft that the prepared fondant has more body than the mold itself.
post #13 of 20
For the first impression mold I pull the excess to the center and cut it with scissors. Sometimes I use a palette knife, depending on the mold.
Edna icon_smile.gif
Visit my website.. www.designmeacake.com
http://designmeacakeblog.blogspot.com/
Check my Gumpaste Tutorials in You tube
http://www.youtube.com/user/tonedna1
Check my new Blooms and Vines DVD!



Thanks Edna
Reply
Visit my website.. www.designmeacake.com
http://designmeacakeblog.blogspot.com/
Check my Gumpaste Tutorials in You tube
http://www.youtube.com/user/tonedna1
Check my new Blooms and Vines DVD!



Thanks Edna
Reply
post #14 of 20
I cut a straight edge in my rolled fondant before placing it in the mold. Then I line up the straight cut edge with the straight edge of the top of the mold. Then place the top piece of the mold on the fondant and gently work the two pieces of the mold together with a small rolling pin. If the bottom lace edge doesn't separate completely, it generally witll with a little 'nudging' with an exacto knife. I had to mess around with the molds a few times before I got my process worked out. Now I really like and use them a lot. Good luck to you!
We make a living by what we get, but we make a life by what we give. Winston Churchill
Reply
We make a living by what we get, but we make a life by what we give. Winston Churchill
Reply
post #15 of 20
Again, sorry you are having issues -- Please see the 2 email I sent you last night that contain links to detailed instructions and how-tos on 2 sided lace molds -- then if you are still haveing issues, let me know

Melissa
Decorate the Cake
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Cake Decorating
Cake Central › Cake Forums › Cake Talk › Cake Decorating › FRUSTRATED with silicone lace molds